How To Start Eliminating 2d Drawings With Creo Ptc

Manage parts or workplanes in views

Use the Manage commands to define the component list of a:

• 2D view inside the Creo Elements/Directly Annotation Module.

• Docuplane within the 3D Documentation Module.

If you select a docuplane belonging to a multi-section, Creo Elements/Direct Modeling applies whatever changes you lot make to every other docuplane of that multi-department.

The following help information describes the Creo Elements/Direct Annotation scenario.

Removing parts from a view can both simplify the representation, and also speed upwardly drawing generation operation.

The following graphic illustrates the removal of several components from a 2nd cartoon:

1. Shows the 3D model before creating the 2d drawing. This view is similar to the auxiliary viewport that is displayed when Creo Elements/Direct Note asks you to select the components to be removed.

ii. Shows the initial second cartoon containing all components. Afterwards selecting this view in Manage, Creo Elements/Directly Note displays the auxiliary viewport. Parts p1, p2, and p3 were removed using the Rem Selected filter.

3. Shows the redrawn 2D drawing with the specified components removed.

To remove or add components from a view,

1. Create the initial 2D drawing in the usual mode.

ii. Click Annotation and then, in the Setup group, click Manage. The Manage Parts / Workplanes dialog box opens.

3. Specify one or more views and wait for Creo Elements/Direct Notation to display the auxiliary viewport. (When multiple views are selected, only a subset of the options is bachelor.)

four. Click Removed or Remaining to choose which parts to brandish in the auxiliary viewport.

five. Select one or more of the post-obit size filter options if necessary:

◦ Threshold %

The relative size of each part or workplane is calculated for both directions (width and height). By default, this size is relative to the total view size, but the size reference tin can be inverse with the options Parent and Siblings described below.

Only parts or workplanes where the relative size is below the threshold for width and pinnacle are considered for adding or removing.

To eliminate the sleeve in the following, a threshold of fifty% was set:

◦ Parent

The size reference for a role or workplane is not the view's size, simply the size of the parent assembly.

◦ Siblings

The reference size (view size or parent assembly size) is divided corresponding to the number of parts inside the parent assembly.

◦ Rem Minor or Add Small

Finally, after defining the rules, you tin apply them to remove or add parts by size criteria.

6. Under Other Filters, if necessary, click Rem Selected or i of the following options to remove parts from or add parts to the 2nd cartoon:

◦ Rem Lib Part or Add together Lib Role

Allows specification of library parts, such equally screws and bolts.

◦ Rem Invisible or Add Invisible (But in Creo Elements/Direct Note)

Specify whether or non to remove or parts or workplane from the view'south component list that are not visible . (Creo Elements/Direct Note commencement scans the 2D geometry in the view to identify which parts or workplanes are actually visible in this view.)

This option is particularly powerful for particular views or for assemblies with many hidden parts asit can reduce the time needed to update views significantly.

Yous must update the view at to the lowest degree once before using this option.

◦ Rem All or Add All

Use Rem All to remove all parts nether the view owner from the view's component list. Use Add All adds all bachelor parts or workplanes to the view component listing.

◦ Rem Container or Add Container

Add together Container and Rem Container add or remove containers created in the Office & Assy carte du jour.

◦ Rem Selected or Add Selected

Use Rem Selected and Add Selected to control manually which parts or workplanes should be included in the view component list. When a unmarried view is selected, Creo Elements/Direct Annotation displays the parts or workplanes removed (or remaining, see Footstep 5), in the auxiliary viewport. When multiple views are selected, Creo Elements/Directly Annotation shows all parts or workplanes in the preview.

◦ Create Part Group

Use the Removed and Remaining options to create function groups representing the removed or remaining parts of the view. The part groups are added to the viewset owner and can be used to show all removed parts, to save only remaining parts, or to modify the components listing of other views in the same manner.

This pick is valid for unmarried view option only.

• Click a view in the Creo Elements/Direct Annotation viewport to add or remove components past copying another view's component list. You must articulate the selected view's component list where you want to add together or remove components, before you copy some other view's component list to the selected view. • Workplanes are not included in a parts grouping.

vii. Click to end your selection.

8. Update the view.

Creo Elements/Direct Note does non handle coordinate systems exactly the aforementioned style as it handles parts. A coordinate system is displayed in the auxiliary viewport even when it is not in the components list. If a coordinate organisation is removed from the components list without removing its related part, information technology is not displayed in the auxiliary viewport. To add together such a coordinate system to the view component list, you must double-click the coordinate organization in the Creo Elements/Direct Modeling Structure Browser.

Source: https://support.ptc.com/help/creo/ced_modeling/r20.1.1.0/en/ced_modeling/OSDM_Annotation/am_view_manage.html

Posted by: smithoneten.blogspot.com

Share this post